Using Skill Defaults
GURPS is built around skills. Choosing a character’s skills is often the most time-consuming part of character creation. During play, most success rolls occur against skill levels. As a result, being able to streamline skills is a good way to speed up GURPS.
During the game, players can use their character’s skills by referring to the character sheet they wrote during character creation. However, there will be some situation in which a player needs his or her character to improvise during a game. For instance, a character may need to attempt a skill for which he or she has no training—such as administering first aid while rushing an ally to a medical facility. Or, the character might need to use a skill outside of his or her comfort zone. For instance, a priest might need to interpret the religious symbols of a cult of demon-worshippers.
The mechanic that GURPS uses for improvised skills is default levels. The “default level” of a skill allows any character that would be familiar with the skill to attempt it, much as a real person could attempt to administer first aid with no specialized training, simply by relying on what he or shes knows from common knowledge. The official rules for default skills are listed on p. B173.
There are two ways to use skill defaults in GURPS. First, characters can attempt skills at the default level based on their controlling attribute. For instance, DX-based skills like Acrobatics and Guns allow the character to roll against their dexterity attribute with an appropriate penalty. Second, characters can attempt unknown skills that default to another related skill that the character does know. For instance, a character with the Physician skill can attempt a Diagnosis skill based on a penalized level of his or her Physician skill.
Skill defaults are useful for making character sheets manageable, but learning the default levels can be tricky. By using a “default” default level, you can simplify skill defaults while keeping the gameplay reasonably consistent.
Defaulting from Attributes
In general, skills default to the controlling attribute based on the difficult of the skill:
- Easy skills default to Attribute-4
- Average skills default to Attribute-5
- Hard skills default to Attribute-6
- Very Hard skills usually don’t have a default
There are exceptions to these rules. For instance, Submarine is a DX/Average skill that defaults to DX-6; Lip Reading is an Average Perception skill that defaults to Perception-10!
These rules create two points for confusion during play. First, players and the GM need to remember how difficult a skill is, which is tricky because it’s not written on the character sheet. Second, they need to remember if this skill follows the standard pattern or if it has an unusual default.
If you are willing to tweak the rules, you can simplify this situation. As a house rule, determine that all skills that can default to an attribute have a default of Attribute-5. Most skills are average, so this default is spot on for most skills, and it’s only off by one for other skills. It’s a small tradeoff for a massive simplification of the rules during play.
Even with this house rule, the GM should feel free to rule that a particular skill doesn’t have a default. Esoteric skills, forbidden knowledge, and skills that require years of dedicated training usually don’t have a default even in rules as written (RAW). By using his or her judgment to rule certain skills un-defaultable, the GM can avoid the worst case abuses.
Defaulting From Known Skills
Because lots of skills overlap, it’s possible that a character will have a skill that defaults to the needed skill. Instead of defaulting from the controlling attribute, the default is calculated relative to the related skill that the character possesses.
Skill-to-skill defaults are even more inconsistent than skill-to-attribute defaults. In Basic Set, the default penalties range from -2 for closely related skills to an all-but-impossible -12 (for attempting to perform surgery based solely on the First Aid skill). Setting aside penalties for defaulting from one specialization to another specialization within the same skill, the chart below shows the frequency of the various skill-to-skill default penalties:Looking up these defaults in play can dramatically slow down play. But, it’s possible to choose a reasonable house rule to simplify the situation. Simply rule that skill-to-skill defaults have a -4 penalty. Choosing a -4 penalty is within one for 75% of the skill-to-skill defaults, which is a pretty good approximation. This house rule also makes sense alongside the skill-to-attribute default house rule because skill-to-skill defaults are marginally better than skill-to-attribute defaults: there’s a small bonus for investing in related skills.
Maintaining the GM’s Discretion
Whether you use the rules as written to handle skill defaults or you use the house rules in this post, remember that the GM has the final say about what skills apply in what situations.
GMs should take care to be fair about what falls under a specific skill. Especially with newer GURPS players who aren’t familiar with the long skill list, with quick-start games that minimize character creation time, and with fast-paced games, taking a hard line on what exactly a skill involves is likely to cause frustration. If the player has a plausible explanation for why their skill is relevant, think carefully about what you gain by disagreeing.
On the other hand, the GM should feel comfortable in ruling that defaults are inappropriate for extra-difficult or specialized skills, especially when there is an in-game reason for the decision (e.g., Thaumatology is unknown outside of the cabal of practitioners or there’s no way a typical character in that world would have any knowledge of spaceship mechanics).
Summary of “Default” Default House Rules
Skill-to-Attribute Defaults: A player may attempt a skill at default by applying a -5 penalty to the controlling attribute. The GM has the final say on whether the skill permits a default attempt and what the controlling attribute is.
Skill-to-Skill Defaults: A player may attempt a skill at a default level by applying a -4 penalty to a known, related skill. The GM has the final say on whether the skill permits a default attempt and which related skills can be used.
Handling Edge Cases: If the Skill-4 default is worse than the Attribute-5 default, the GM can choose to either use the better default (the simplest option) or let the player roll against Attribute-4 (which preserves the mild bonus for knowing a related skill). This could happen if the related skill is a Hard or Very Hard skill and the character only knows the related skill at Attribute-1 or less.